Difference between revisions of "Production Run tests"

From Opentaps Wiki
Jump to navigationJump to search
m (Protected "Production Run tests": Sysop page [edit=sysop:move=sysop])
(→‎Material Issuance Tests)
 
(4 intermediate revisions by 2 users not shown)
Line 1: Line 1:
−
'''Action'''
+
== Material Issuance Tests ==
  
−
Create, schedule and confirm a production run which will use up inventory for a product greater than the amount available. EG. if a production run component task requires 3 * PRODUCT_A, make sure that total QOH for PRODUCT_A is below 3 before beginning. Start the relevant task running and click [Issue Components].  
+
These tests require that the QOH of MAT_A_COST is 0 and the QOH of MAT_B_COST is greater than 100.
  
−
'''Results'''
 
  
−
A red error message saying <font color="red">Warning: This will cause QOH of product ${productId} to become negative</font> should appear at the top of the page for each product with insufficient inventory. Clicking the [Issue Components] link again should result in a confirmation dialog, and clicking 'OK' should result in the components being issued successfully.
+
'''Action 1'''
 +
 
 +
* Click on Warehouse > Manufacturing > Create A Production Run
 +
* Enter a ProductID of "PROD_COST"
 +
* Enter a Quantity of "2"
 +
* Click [Create]
 +
 
 +
* On the next page "Edit Production Run" click the [Confirm] button near the top of the page
 +
 
 +
* When the page refreshes click the [Start] button in the "Tasks" section.
 +
 
 +
'''Results 1'''
 +
 
 +
The list of Materials has a new button [Issue Additional Materials].  Each product for the task is listed:
 +
 
 +
*  MAT_A_COST with Qty Issued 0 and an input box in the Needed column containing the default qty to issue of 4.
 +
*  MAT_B_COST with Qty Issued 0 and an input box with default qty to issue of 6
 +
 
 +
'''Action 2'''
 +
 
 +
Press the [Issue] button to submit the default quantities for MAT_A_COST (4) and MAT_B_COST (6).
 +
 
 +
'''Results 2'''
 +
 
 +
The page reloads with a warning in red at the top of the page:  '''Warning: This will cause QOH of product MAT_A_COST to become negative'''  No warning about MAT_B_COST.  [Issue] button has changed to [Force Issue].  The qty needed is still the same as before (4 and 6).
 +
 
 +
''Action 3'''
 +
 
 +
Pres [Force Issue].  A popup confirm dialog comes up.  Confirm the action.
 +
 
 +
'''Results 3'''
 +
 
 +
Page reloads with the following differences:
 +
 
 +
*  Task now has a [Complete] button next to it.
 +
*  Qty Issued for MAT_A_COST is 4
 +
*  Qty Issued for MAT_B_COST is 6
 +
*  No [Issue] button and no input boxes for Needed qty.  This column should be gone.
 +
 
 +
'''Action 4'''
 +
 
 +
Create and [Confirm] another production run for 2 of PROD_COST.  [Start] the task.  Enter 0 for quantity needed for MAT_A_COST.  Enter 1 for MAT_B_COST.  Press [Issue].
 +
 
 +
'''Results 4'''
 +
 
 +
The issuance should be successful and there should be no warnings and no [Force Complete].  Qty Issued for MAT_A_COST is still 0.  The qty needed for MAT_A_COST is still 4.  Qty issued for MAT_B_COST has increased to 1.  Qty needed for MAT_B_COST is down to 5.
 +
 
 +
'''Action 5'''
 +
 
 +
Issue 1 of MAT_A_COST and 1 of MAT_B_COST.
 +
 
 +
'''Results 5'''
 +
 
 +
The page reloads with a warning that MAT_A_COST will have negative QOH.  The [Force Complete] button comes up.  The quantities in the input boxes for Needed are:  1 for MAT_A_COST and 1 for MAT_B_COST.
 +
 
 +
'''Action 6'''
 +
 
 +
[Force Issue] the issuance and confirm.
 +
 
 +
'''Results 6'''
 +
 
 +
Page reloads with successful action message.  Quantity issued for MAT_A_COST is now 1, while quantity Needed in input box is 3. Quantity issued for MAT_B_COST is now 2 and the needed quantity is now 4.
 +
 
 +
'''Action 7'''
 +
 
 +
Issue the remaining 3 MAT_A_COST.  Enter 6 for MAT_B_COST needed (to simulate spending 2 extra material due to losses).  Force the issuance through.
 +
 
 +
'''Results 7'''
 +
 
 +
Issuance is successful and the Needed column with the [Issue] button is no longer there.  Qty issued for MAT_A_COST is 4.  Qty issued for MAT_B_COST is 8.
 +
 
 +
== Issuing more Materials to a Task ==
 +
 
 +
Ensure that the QOH for GZ-1000 is 0 and GZ-1001 is greater than 100.
 +
 
 +
 
 +
'''Action 8'''
 +
 
 +
Press [Issue Additional Materials].  A form to issue extra products to the task comes up.  Issue 2 of GZ-1000 (should be QOH 0).
 +
 
 +
'''Results 8'''
 +
 
 +
The input form reloads with warning that GZ-1000 QOH would become negative.  [Force Issue Additional Materials] button comes up.
 +
 
 +
'''Action 9'''
 +
 
 +
Force the issuance through.
 +
 
 +
'''Results 9'''
 +
 
 +
Production run screen should reload showing that 2 GZ-1000 was issued in the list of Materials.
 +
 
 +
'''Action 10'''
 +
 
 +
[Issue Additional Materials] for 5 GZ-1001 (which should have QOH > 100).
 +
 
 +
'''Results 10'''
 +
 
 +
No Force issuance required.  Production run screen loads immediately showing 5 GZ-1001 issued.
 +
 
 +
'''Action 11'''
 +
 
 +
[Issue Additional Materials] for 2 MAT_B_COST.
 +
 
 +
'''Results 11'''
 +
 
 +
No force issuance required.  Production run screen loads immediately showing 10 total MAT_B_COST issued.

Latest revision as of 23:36, 21 November 2007

Material Issuance Tests

These tests require that the QOH of MAT_A_COST is 0 and the QOH of MAT_B_COST is greater than 100.


Action 1

  • Click on Warehouse > Manufacturing > Create A Production Run
  • Enter a ProductID of "PROD_COST"
  • Enter a Quantity of "2"
  • Click [Create]
  • On the next page "Edit Production Run" click the [Confirm] button near the top of the page
  • When the page refreshes click the [Start] button in the "Tasks" section.

Results 1

The list of Materials has a new button [Issue Additional Materials]. Each product for the task is listed:

  • MAT_A_COST with Qty Issued 0 and an input box in the Needed column containing the default qty to issue of 4.
  • MAT_B_COST with Qty Issued 0 and an input box with default qty to issue of 6

Action 2

Press the [Issue] button to submit the default quantities for MAT_A_COST (4) and MAT_B_COST (6).

Results 2

The page reloads with a warning in red at the top of the page: Warning: This will cause QOH of product MAT_A_COST to become negative No warning about MAT_B_COST. [Issue] button has changed to [Force Issue]. The qty needed is still the same as before (4 and 6).

Action 3'

Pres [Force Issue]. A popup confirm dialog comes up. Confirm the action.

Results 3

Page reloads with the following differences:

  • Task now has a [Complete] button next to it.
  • Qty Issued for MAT_A_COST is 4
  • Qty Issued for MAT_B_COST is 6
  • No [Issue] button and no input boxes for Needed qty. This column should be gone.

Action 4

Create and [Confirm] another production run for 2 of PROD_COST. [Start] the task. Enter 0 for quantity needed for MAT_A_COST. Enter 1 for MAT_B_COST. Press [Issue].

Results 4

The issuance should be successful and there should be no warnings and no [Force Complete]. Qty Issued for MAT_A_COST is still 0. The qty needed for MAT_A_COST is still 4. Qty issued for MAT_B_COST has increased to 1. Qty needed for MAT_B_COST is down to 5.

Action 5

Issue 1 of MAT_A_COST and 1 of MAT_B_COST.

Results 5

The page reloads with a warning that MAT_A_COST will have negative QOH. The [Force Complete] button comes up. The quantities in the input boxes for Needed are: 1 for MAT_A_COST and 1 for MAT_B_COST.

Action 6

[Force Issue] the issuance and confirm.

Results 6

Page reloads with successful action message. Quantity issued for MAT_A_COST is now 1, while quantity Needed in input box is 3. Quantity issued for MAT_B_COST is now 2 and the needed quantity is now 4.

Action 7

Issue the remaining 3 MAT_A_COST. Enter 6 for MAT_B_COST needed (to simulate spending 2 extra material due to losses). Force the issuance through.

Results 7

Issuance is successful and the Needed column with the [Issue] button is no longer there. Qty issued for MAT_A_COST is 4. Qty issued for MAT_B_COST is 8.

Issuing more Materials to a Task

Ensure that the QOH for GZ-1000 is 0 and GZ-1001 is greater than 100.


Action 8

Press [Issue Additional Materials]. A form to issue extra products to the task comes up. Issue 2 of GZ-1000 (should be QOH 0).

Results 8

The input form reloads with warning that GZ-1000 QOH would become negative. [Force Issue Additional Materials] button comes up.

Action 9

Force the issuance through.

Results 9

Production run screen should reload showing that 2 GZ-1000 was issued in the list of Materials.

Action 10

[Issue Additional Materials] for 5 GZ-1001 (which should have QOH > 100).

Results 10

No Force issuance required. Production run screen loads immediately showing 5 GZ-1001 issued.

Action 11

[Issue Additional Materials] for 2 MAT_B_COST.

Results 11

No force issuance required. Production run screen loads immediately showing 10 total MAT_B_COST issued.

Retrieved from "https://docs.opentaps.org/docs/index.php?title=Production_Run_tests&oldid=1598"